VoltaELECTRICAL ESTIMATING
Blog · Guide

How to estimate an electrical panel upgrade in Canada (2026)

A 100A to 200A service upgrade is estimated as a short list of line items: panel and breakers, meter base and mast, service conductors, grounding, one crew-day of labour, the permit and the utility’s disconnect and reconnect. Published 2026 contractor prices put a straightforward job at roughly $2,500 to $7,000 CAD depending on the city, and underground or relocated services can run past $10,000. The swing comes from the service entrance and the utility, not the panel, so price those first.

Figures below come from the regulators, utilities and contractors linked inline and listed under Sources, checked on November 16, 2026. Contractor prices are their published ranges, not quotes. VOLTA makes one of the products mentioned.

Key takeaways
  • Run the load calculation first. The service size comes out of CEC Section 8, not out of the customer’s wish list.
  • Price the service entrance before the panel: overhead vs underground, meter base condition and any relocation move the number most.
  • Labour is usually one day on site: a journeyperson and an apprentice for 6 to 10 hours, per a Vancouver contractor’s published breakdown.
  • Permits are small but specific: $332 from Technical Safety BC (service upgrade up to 200A, 2026), $92 from ESA in Ontario, and about $167 on a $5,000 job in Calgary.
  • The utility side is its own line. BC Hydro’s published minimum for an overhead service up to 200A is $880 plus GST.

What should you check before you price a panel upgrade?

Four things, on site or from photos, before any number goes on paper.

  1. The load calculation. Whether the house needs 200A is a CEC Section 8 calculation (Rule 8-200 for single dwellings). A Calgary contractor’s guide notes the City requires a qualified electrician to do it, even on homeowner permits (Voltra Electrical). An EV charger alone may be handled with a load management device instead of an upgrade. For how editions and provincial amendments work, see the CEC for electrical estimators.
  2. Overhead or underground. An overhead mast is quick to replace; an underground service may need a new conductor to the property line. That single fact is the biggest cost driver in every contractor guide cited here.
  3. Meter base, mast and grounding. A 100A meter base and service entrance are usually sized for the old service and change too. Older homes may need new ground rods and bonding.
  4. Panel location and existing wiring. If the panel must move to meet current clearances, or the branch wiring is knob-and-tube or aluminum, the job grows. A Vancouver contractor notes that legacy branch wiring can stop the new panel being energized until it is remediated (LGD Electric).

What line items go into a 200A panel upgrade estimate?

The table below lists the lines a complete estimate carries, with the published ranges contractors give for each. Use them to check your own supplier prices, not to replace them.

Line itemWhat it coversPublished range (CAD)
200A panel and breakersPanel, main breaker, branch breakers (AFCI/GFCI where required)$500 to $1,200 (LGD Electric, Vancouver)
Meter base200A meter socket approved by the utility$150 to $400 with masthead (LGD); $300 to $600 replacement (Einwechter Electric, Ontario)
Service entrance cable or mastConductors from the masthead to the panel, mast and weatherhead$100 to $300 conductor (LGD); $400 to $1,100 cable or mast (Einwechter)
Grounding and bondingGround rods, clamps, bonding conductorsPrice from your supplier; check the existing electrode
LabourJourneyperson and apprentice, one day on site$1,500 to $3,000 (LGD)
Permit and inspectionAuthority having jurisdiction for the siteSee permits
Utility disconnect and reconnectWork on the utility side of the meterSee utility coordination
Sub-panel (if added)Garage, suite or addition$900 to $1,800 (Einwechter)
Underground re-cable (if needed)New service conductor from the transformer$5,000 to $15,000 (Einwechter)

Keep the permit and the utility charge on their own lines. They are not material, they do not take the same tax treatment, and the utility charge may be billed to the owner directly. Our markup guide explains why pass-through costs and taxed material should not share a line.

How many labour hours does a 100A to 200A upgrade take?

Contractors publish the time on site rather than labour units, and they agree closely:

SourcePublished time
LGD Electric, VancouverJourneyperson plus apprentice, 6 to 10 hours on site
Voltra Electrical, CalgaryUsually one day on site, power off roughly 3 to 8 hours
SparkBC, Metro VancouverStraight swap 1 day; with new meter base 1 to 2 days; with service relocation 2 to 3 days

For the estimate, convert that to crew-hours (two people for 9 hours is 18 hours) and add the time that never shows on site: the load calculation, the permit application, booking the utility and the inspection, and labelling the new panel. If you build labour from units instead, keep the steps separate: quantity × unit × factor, then × loaded rate. Electrical labour units explained covers the method, including why supervision is outside published units.

What does the permit cost for a panel upgrade in BC, Ontario and Alberta?

The permit is usually the smallest line, and the easiest to get exactly right because it comes from a published schedule.

Province / cityWho issues it2026 fee for a residential service upgrade
BC, most of the provinceTechnical Safety BC$332 for a service upgrade or relocation up to 200A ($349 from January 1, 2027); $513 for 201 to 400A (TSBC fee schedule)
BC, Vancouver, Burnaby, Surrey and other permitting municipalitiesThe cityThe city’s own schedule; see BC electrical permit cost
OntarioElectrical Safety Authority (ESA)$92 contractor fee for a service or panel change filed on its own, per ESA’s 2026 fee guide as cited by Einwechter Electric; see ESA permits in Ontario
Alberta, CalgaryCity of Calgary$112 processing fee + $9.79 per $1,000 of construction value, plus the 4% Safety Codes Council fee: about $167 on a $5,000 job; see Calgary electrical permit cost
Alberta, EdmontonCity of EdmontonCity schedule; see Edmonton electrical permit cost and Alberta permits

Two rules worth putting in your notes. In Ontario, the notification has to be filed before the work starts, or within 48 hours after it starts when filing first is not practicable. In Calgary, a homeowner permit cannot cover the main service, main panel, main breaker or meter base, so the contractor pulls it, and the meter base needs a City “green sticker” before ENMAX re-energizes the home (Voltra Electrical). In Toronto the permit side is the same ESA notification; see Toronto electrical permit cost.

How do you coordinate the utility disconnect and reconnect?

Every service upgrade needs the utility to pull the meter and reconnect after inspection, and the utility charges for its side separately. Price it as its own line and say on the quote who pays it.

  • BC Hydro. Its published minimum charges cover upgrades and alterations with new wire or cable: $880 plus GST for an overhead single-phase service up to 200A, $1,400 plus GST underground, and $820 plus GST for an alteration of existing wire. A meter installed at the same time as the service connection is $64 plus GST, and a call-back because the site was not ready is $351 plus GST (BC Hydro). One Vancouver contractor reports about $1,200 paid to BC Hydro directly and 1 to 2 weeks of BC Hydro scheduling on a typical job (LGD Electric); another quotes a 2 to 4 week lead time for the disconnect (SparkBC).
  • Ontario. The local distribution company disconnects the house and reconnects it after ESA has passed the work (Einwechter Electric). Ask the utility for its own service-change charge rather than assuming one.
  • Calgary. Upgrades go through ENMAX’s Get Connected process, and work on the utility side of the meter is quoted by ENMAX, or by FortisAlberta in much of the surrounding region (Voltra Electrical).

The call-back charge is the one to protect against: schedule the inspection and the reconnect for the same day only when you are confident the work will pass, and put a line in your risk allowance if you are not.

How much does a 100A to 200A panel upgrade cost in Canada in 2026?

Published 2026 contractor prices, all in CAD:

RegionScopePublished rangeSource
Metro VancouverStraight 100A to 200A panel swap, incl. permit, BC Hydro coordination, inspection$3,500 to $5,000SparkBC
Metro Vancouver200A upgrade with new meter base$5,000 to $6,500SparkBC
Metro Vancouver200A upgrade with service relocation$6,500 to $9,000SparkBC
City of Vancouver100A to 200A, all-in incl. permit and BC Hydro fee$3,500 to $7,000LGD Electric
Ontario100A to 200A, compiled from Ontario contractors’ 2026 guides, before HST$1,500 to $6,500+, most $2,500 to $5,000Einwechter Electric
Calgary100A to 200A, incl. panel, breakers, permit, inspection$2,500 to $6,000Voltra Electrical
CalgaryUnderground, new conductor to the property line$7,000 to $10,000+Voltra Electrical

Treat the spread as information. A quote at the bottom of the range usually assumes an overhead service, a reusable meter location and no surprises in the branch wiring. If your site visit found any of those, your number should sit higher, and the line items above show the client why.

A worked example: overhead 100A to 200A upgrade in a Technical Safety BC area

A detached house in a BC municipality served by Technical Safety BC, overhead service, meter staying in place. Inputs are illustrative: replace them with your supplier quotes and your own rates.

LineCalculationAmount (CAD)
Material: panel, breakers, meter base, service conductor, mast fittings, groundingsupplier quote$1,600.00
BC PST paid by the contractor on that material7% × $1,600$112.00
Labour20 crew-hours (2 × 9 h on site + 2 h admin) × $52/h loaded cost$1,040.00
PermitTechnical Safety BC, service upgrade up to 200A, 2026$332.00
Direct job cost$3,084.00
Price at a 30% target margin$3,084 ÷ 0.70$4,405.71
GST5% × $4,405.71$220.29
Electrical contract total$4,626.00
BC Hydro service charge (billed by BC Hydro; minimum for overhead up to 200A)per BC Hydro$880 plus GST

The $52 loaded rate and 30% margin are carried over from our markup worked example; set your own. The result lands inside the Metro Vancouver ranges above, which is the check you want: if your number falls well outside published ranges, find the line that explains it before you send the quote.

How does VOLTA handle a panel upgrade estimate?

VOLTA prices the upgrade the same way the table above does: material, labour with NECA-style factors, permit and mobilization on their own lines, then your markup and the province’s tax. Enter the permit fee under Permits + mobilization and it prints as a separate line on the quote. When the job comes with drawings, VOLTA’s panel schedule reader picks up panel designations and service size from the PDF text and drafts the distribution lines, and the PDF takeoff drafts the rest in the browser for you to review. It does not run the load calculation or check code compliance for you, and it does not book the utility. $9.99 CAD a month after a 30-day free trial; see residential estimating.

Frequently asked questions

How much does it cost to upgrade from 100 amp to 200 amp in Canada?
Published 2026 contractor prices run about $3,500 to $7,000 in Metro Vancouver, mostly $2,500 to $5,000 before HST in Ontario, and $2,500 to $6,000 in Calgary for a straightforward job. Underground services, new meter bases and relocations push the total higher, sometimes past $10,000.
How long does a 200 amp panel upgrade take?
Usually one day on site. A Vancouver contractor publishes 6 to 10 hours for a journeyperson and an apprentice, and a Calgary contractor reports the power off for roughly 3 to 8 hours. Permits and utility scheduling add lead time before the work day.
How much is the permit for a service upgrade in BC?
In areas served by Technical Safety BC, a contractor permit for a service upgrade or relocation up to 200A is $332 in 2026 and $349 from January 1, 2027. Vancouver, Burnaby, Surrey and the other municipalities that issue their own electrical permits use their own schedules.
Who pays the utility's disconnect and reconnect charge?
It depends on the utility and the contract, so say it on the quote. BC Hydro publishes a minimum of $880 plus GST for an overhead single-phase service up to 200A, and some contractors have the owner pay BC Hydro directly. In Calgary, work on the utility side of the meter is quoted by ENMAX.
Does every house need 200 amps?
No. The CEC Section 8 load calculation decides it. Many 100A homes can add an EV charger with a load management device; several large new loads such as a heat pump, an EV charger and a hot tub usually tip the calculation toward 200A.

Sources

Each source was opened and checked on November 16, 2026.

  1. Technical Safety BC, Fee schedule: Electrical (2026 and 2027)
  2. BC Hydro, Charges and fees for electrical connections
  3. LGD Electric, 200-amp panel upgrade cost in Vancouver (2026)
  4. SparkBC Electric & Design, How much does a 200A panel upgrade cost in Metro Vancouver? (May 7, 2026)
  5. Einwechter Electric, Electrical panel upgrade cost in Ontario (2026), prices checked October 25, 2026
  6. Voltra Electrical, 100 amp to 200 amp panel upgrade cost in Calgary (updated November 6, 2026)
  7. VOLTA, Master electricians, permits and the code: what an Alberta electrical quote has to carry in 2026 (City of Calgary 2026 fee schedule figures)
  8. VOLTA, ESA permits, licences and the code: what an Ontario electrical quote has to carry in 2026

Price your next panel upgrade line by line. Permit, utility and material on their own lines, your markup and the right provincial tax on top. 30-day free trial (card required, $0 today), then $9.99 CAD/month plus applicable tax.

Start the 30-day free trial

Next: How to calculate markup on electrical estimates · What an electrical permit costs in BC · Cost to wire a house in BC · Electrical change orders and addenda